lots of stuffffffffffffffffff

Posted: Tue Apr 29, 2008 5:30 pm Post subject: lots of stuffffffffffffffffff

Local guys come get it cheaper. call me for a price Ill hook you guys up

I'm cleaning out "some" parts I have at my parents house. LOL I have tons of car stuff. This is just 3800 serise II and III (95 97+) stuff. I've thrown out like 5 garbage cans, of 80-100K motor parts. And made 3-4 trips in my truck of scrap metal to junk heavy stuff. Stuff was fine, just needed to be cleaned, But I don't have the time. I'm only keeping clean/new parts. But I dont need 4-5 of the same clean low millage parts. So these are good spare parts (no worn out junk) to get some more room. To nice to thow out. If you not local, Im not going to bother to ship out a $10 part so must buy a few little things then that add to Min $15.

PM's list the parts is question is the title, and keep it there. And quote last/all Pms and replys so I can keep track of you, the parts, and the transaction. No dibs, unless your've bought more before or cool. If your a retard and can't follow directions on getting me payment, I'm not gona sell it to you. Simple.

Im a great seller.
http://www.clubgp.com/newforum/tm.asp?m=4127333&p=1&tmode=1&smode=1
http://www.clubgp.com/newforum/tm.asp?m=4139064&p=3&tmode=1&smode=1
http://www.clubgp.com/newforum/tm.asp?m=4354611&p=1&tmode=1&smode=1

L67 valve covers, cleaned, inside has some oil stains (fiberglass they all do) but no buildup. Ready to bolt on, or paint. SOLD

New GM never used 3800 flexplate, Drilled for 2 bolt patters $40

New GM L67/L32 valve cover gaskets. GM lists at 37-45new. this set $30

New felpro L67/L32 valve cover gaskets with bolt gaskets. this set $36

GM 3800 lifter trays, clean low milage, no damage. $10

3800 rockers, I don't remember the year off these, But there clean, no oil staining, r wear on them. replace you dirty, hi millage ones $30

3800 rocker stands. same thing, nice low milage $10

New GM 3800 cam bolt unopened in bag SOld
NEW GM 3800 timming chain damper SOLD

Drilled 160 Tstat, with good Oring $7
EGR "penny mod" block off plates. Have them for LIM, and rear mani $5 each

GM LS6 valve springs. set of 12. Not the more common "full yellow" paint 2003+ and current 243 heads. These are a good take off set from a 01-03 car, used for a few thousand miles on a stock L67 cam with 1.9 stock rockers. $40

Comp cams mixed 105/130 (6/6) The 105s (915) are new never installed. The 130 (918s) are were installed for only a few hundred miles, then removed to step down to the other 915 (new set). Both these are from a few years ago made PAC making them better then any current comp junk. I used the others of these sets on my car 11.4 M90 XPZ cam'd
New (never installed), and Like new (1-200 miles) asking $120

Good soft 3800 Evap line $10
super clean 3800 crank sencore wiring cip thigher, no damage $5
same..... ispection cover $5
same.... SSEI M90 plug wire holder. Theses are nicer then the GTP/GS ones. $5
New NAPA front cotraol arm (rear) bushing. $9 each

Trans dipstick tube. Bent to work with TOG heads, has more room with a turbo DP also. clears the larger brake booster too. Has high temp pading to no cause fasle KR if your running non soild motor/trans mounts. Comes with level wand too. Great shape, no damage, rust or anything $40

4t65 HD diff cover, replace you damaged or broken form a diff explosion. No damage, with good seal, and bearing. Super clean, like new $40

oil pan, with gasket. Gasket wasn't leaking, has windage tray. Pan is in great shape with no dents, rust or damage. It was professional washed out in a parts washer (the chalky color form the cleaner) ready to bolt on. $40

Milled oil pump cover. Milled .025 for added room for dual roller timming chains. Dont go getto with 2 gaskets. Higher risk of gasket leak, and your main oil feed. That will damage your motor. $40 ready to bolt on for your cam swap, no cores or down time.

Eaton supercharger cuplar. Very clean, low millage still fits press tight. $12
L67 SC belt idler stand, cleaned, and painted gunmetal. Ready to bolt on for you old damaged stripped, or L67 swap $7
O2 spoof works great no SES lights, theses are hard to find now. :snky: $30

Alt bracket/head hose, tensor housing. clean, painted gunmetal. Tenior is like new, only has about 24K on these. No correions, or stripped threads. Also is machined for added room for hi flow intercooler core fitting. $35

Ricer headlights, I used these on my red gtp for about 1 week, people made fun of me. There tuner style HID /plazma blue, mad panty droppers as Ed would say. sold

gen3 m90 rotors, some normal teflon peeling starting. Outer edge of the inlet side. Still work fine, I went 11's on them XP cam DIY heads. Great set to spray wet thou or meth. $25

New in box 3800 JP dual roller trimming sets $100
New Re usable rocker bolts, Info: http://www.zzperformance.com/grand_prix/products1.php?id=380&catid=104
http://www.intense-racing.com/Merchant2/merchant.mvc?Screen=PROD&Product_Code=INT-RAB&Category_Code=HCV&Product_Count=3
These would cost you about $30 shipped.
Selling for $20 shipped (US)
ZZP/intense 2.60 SC pulley fits 6 and 8rib belts. Black like brent strongs dad. $30

Great shape, like new belts. These are the best NAPA/gates Look at the lengths in the pics. 2 are 8rib, 1 is 6,
060670 - 68 1/8th long $10
080680- 68 1/2 $25
080730- 73 1/2 $27

Don't PM me if these will work on your car, look it up yourself. These aren't for a stock 3800 so your gona need to know a little what parts you have, and what you need. Not all different brand belt PNs are the same measured lengths, no note what I listed there real lengths at.
I used them on all on a 2.2-2.3 thick IC core, 2.5-2.7 SC pulley. The 68.5 with the normal Wbody brackets. 73.5 with the SSEI brackets. Stock sized balancer. The 8 ribs are not cheap $4x new

trans external range switches. These get broke during motor and trans swaps. Good clean working ones. $10 each

GM oil level senors, good, clean low millage $7
3800 cam plates $7
3800 cam magnets $7
3800 ICMs $10
magnetic drain plug ??$5 ?free with other shit
Good low mileage GM 02 sencor $20
m90 PCV cover $5 ?? free with other shit

CompCams 7˚ steel retainers are precision machined from 4140 chromemoly and finished in black oxide. Like new $27

Modified Valve Spring Retainers have been modified to give an extra .030 clearance to the valve seal. They are required when using the XP cam on stock heads. sold

DENSO 02 sencor. Like new, only a few hundred miles on unleaded pump gas. This in said be be fine with race gas. New there like $65 Looking to get $45

3800 timming cover, about 25K miles. Cleaned and painted gun metal, ready to bolt on no damage. Dosn't not come with oil pump cover, but has gears and hardwear. $30

3800 timming cover about 84K miles., Needs to be cleaned, includes oil pump, and good water pump $45. Water pump seprate $20

Engine and trans mount braket. Very clean, ready to bolt on. Or a little time you can take a lot of weight out of them Smile

$20 for the pair

GM sensors. Low milage clean, works great.
cam $20
crank $20

engine dogbones, Need to be cleaned, bushing look great no cracks or damage.
$35

Hi/Low fan switch. Controls the stock fans. Middle in normal PCM control, and has hi and low settings. Great for the track
sold

pushrods. clean, Like new
5/16ths .083 wall 7.00 lenths $100 new, asking $60

GTP dash gauge cluster, works great 130K asking $30

Trans parts: everyting is 4t65e HD I cleaned up alot of spare trans, and extra part. Need to make some room. So these are up for sale, this is just what I have ready to sell, I took a pic of. I still have a lot of trans parts I need to go thu. Ask if you need anything, for your rebuild. Anything from bare case, to little part. Small parts add up anyting at adds up to like $20. I'd rather not waste the time to ship out a $10 part. Unless you have bought parts form me before. Or local pickup is always welcome.

HD output shaft. No damage, Like new. $30

trans pump, SOLD

Side cover gasket, Good non damaged. These new are somthing crazy like $85 new. Looks to get $35 for it.

Pan gaskets, these are good non damaged GMs I saved. Way better then a shit cork one if you dosnt have a GM on your car anymore. They are great gaskets are seal fine. Also new cost alot, $45 I recall. asking $20

Pump shaft. SOLD
Hardened 4th hub shaft. SOLD

HD diff cover (the one in the pic has some dirt on the outside). no damage. must have for you guys racing without a spotter every time Sad

$60

HD diff cover, Not in pic I found this last night. Has some paint marks, Like form a rebuild shop. Its used But was presser washed, or steam claned or somthing Its very clean alum. $70

also has good VSS senors, and diff cover 0rings if you diff take out the Oring with the cover.

Extra new clutchs. Not everything for a full pac setup. But a must have for setting up you trans up tighter to hold more power. With adding a extra clutch, no wave plates ect. about 3-4 clutches/steels for each.
$15

Partial 3.69 single chain set. This is a bad ass upgrade, Zooomer went 9's on this setup. I can't find the drive gear, I hope it turns up. But its the good 7/8th stiff chain, Not the weaker "soft" 7/8 chain some people get. ZZP clains this chain is stonger then the 15/16th chain setup. And the moded gears to bolt in a 4t65hd. And a mint VSS wheel with no damage to the rivets to work with the drive gear. I forgot if I even ran this. It was probably just a back up, for a car I was setting up. Ill get a price tomorrow for full set, and with no drive gear.

trans pan, CLEAN, No dents, bends, rust or anything. $30

I forgot the right name, The drive carrier plant thing? But its the assembly that had the planets gear sets, that gets damaged when debris passes thru the trans fuild. Its mint, planets, and rings have no damage. I recall this part was like $130-$200?? maybe, there a chunk to replace. asking $50

Manual driver seat rack, this is hard to find. I used it to save weight over the power rack. bolts right in, $25

Drilled 180* Tstat SOLD
Drilled 160* Tstat $5
New Alum cradle bushings $15
NEW Timing chain dampener. Just found 1 more , new
NEW GM Timing Chain, SOLD

PS pump, Off a 31K 3800. With pulley. The nipple off the res. is broke. So your have to use your current one. Its very clean, looks new.
$30

NEW GM PS pump, In box, never used. Has the GM install diagram and paperwork.
$70

thanks
John
_________________
New Era performance

01z28, M6 NA, mullet, T tops, siqqqq

Posted: Tue Apr 29, 2008 5:55 pm Post subject:

John, I'm thinking about trying to get the Denso o2 Sensor from you. I'm still getting my P1133 after the TOG's install. I think Shawn said a Denso might help me.
_________________
2000 PONTIAC GRAND PRIX GTP
VS|TOGâ€™s|ZZP II IC|ZZP Stg II TB|Stg 4 Gen III|2.8 MPS

Posted: Tue Apr 29, 2008 6:20 pm Post subject:

Id try a different 02 is your original?

Posted: Tue Apr 29, 2008 6:30 pm Post subject:

I'll take the...

Valve covers
New cam bolt
New 'timming' chain dampener
Magenetic drain plug
_________________
2018 Acadia
Retired: 2014 ATS, 2004 GTP

Posted: Tue Apr 29, 2008 6:47 pm Post subject:

I sent u a PM about the hi/low fan switch
_________________

-2000 Grand Prix GTP silvermist
-2003 Grand Prix GT redfire metallic
-1991 Grand Prix GTP LQ1/Getrag284 5 speed. Neon blue metallic.
-1999 Regal GSE....SOLD.

Posted: Tue Apr 29, 2008 7:35 pm Post subject:

It's my 3rd since the install...

Posted: Tue Apr 29, 2008 7:36 pm Post subject:

just change the PCM them

Posted: Tue Apr 29, 2008 8:01 pm Post subject:

I'll take the hi/low fan switch.....tried senden u another PM....but it wasnt letten me.

Posted: Thu May 01, 2008 12:43 pm Post subject:

ho thats weird. I have to give larry back some parts, Ill be in webster this weekend. you can have it

Posted: Thu May 01, 2008 4:48 pm Post subject:

Yes, Denzo is ALOT better than the Bosch O2 sensor. period. There was quiet a few posts on ClubGP a year or so ago about the Denzo quality over Bosch.

Back on topic.....yay parts fo sale!
_________________
ZZP stuff...
Heads (started as ZZP stg.3 with some improvements)
Cam (XPZ with a slightly different components for valve movment)
IC (Ford Cobra coolant resv., frt exchr the size of a engine rad. weight consum. rear expans. tank)
"Certified Auto Trans Shop" Transmission sold by ZZP...I have no comment for this peice of...great trans. Wink

Also,
SLP Headers <--FOR SALE
Eaton's Gen.3 M90

Posted: Thu May 01, 2008 7:18 pm Post subject:

Posted: Sat May 03, 2008 8:23 pm Post subject:

John how much for the double roller and the milled cover? I'm looking at getting these from ya.

Posted: Sun May 04, 2008 6:56 am Post subject:

John, I'll offer $5 for the headlight bulbs, Jenn likes the look of them I guess. Rolling Eyes

_________________

Posted: Sun May 04, 2008 11:27 pm Post subject:

haha that works eric, call me and we can set a time, Im gona be going to my parents a few nights this week. I can ship them to.

double roller and milled cover I do sell for $140.

Posted: Mon May 05, 2008 5:48 am Post subject:

when and where can I pick them up? Also what about those mod'd retainers that you have? Maybe an all inclusive package kind of thing? Let me know what you can do for all 3 of these and I can PM you my number. I'm all over Rochester throughout the day working so I can pick them up anytime.

	Upstate New York Club Grand Prix Forum Index -> Classifieds	All times are GMT - 5 Hours Goto page 1, 2 Next
Page 1 of 2