4th gen Fbody parts

Posted: Mon Dec 28, 2009 11:41 pm Post subject: 4th gen Fbody parts

Stock steering wheel off my 01, with controls. all bulbs work $40

Good airbags. Driver, undamaged cover like new. passenger side with dash braket. And the control module $150

Front and rear seats. Cloth 2001 Z28, with rails- power driver/ manual passenger. No holes, rips anything broken. And rear fold down seat, with lower cushions (not shown) $300 for everything, bets offer

Stock Y-pipe off my 2001. NO WINTERS $20

Casper O2 sims. $45 one, $80 pair shipped

4th gen washer bottle, with pump works great. Very clean $30

ABS mod off a 01, with bracket. no lines $20

rear rotors, great shape 50K painted with black VHT $50 bets offer

2) 98-00 chrome 16x8 camaro Z28 5spokes rims

Last fall, washed/waxed

I have another pair of these rims, (I have 2 sets) in great shape. With mounted and balanced with
Yokohama AVS ES100 radial. Ultra High Performance Summer tires
http://www.tirerack.com/tires/tires.jsp?tireMake=Yokohama&tireModel=AVS+ES100

Stock sized 245/50/16 they are $263 from tirerack. There in great shape, I ran them for a few months when I had 4 before I got DRs. I'll get a pic of the tread, remember them at 75%. Great summer tire, awesome in the rain if thats possible. I was getting high/mid 1.7's, I think maybe some low 1.7s on the pair I ran on the rear. Got a 1st and 2nd place trophies of the spring and fall MOMs invite, fastest street tire car with them.
Vid with them, bad ass snky tire
http://www.vimeo.com/1822370

I dont have the lug covers for this set.
$300 there ready to go, getting a free tire.

make a offer on splitting them up too.
_________________
New Era performance

01z28, M6 NA, mullet, T tops, siqqqq

Posted: Mon Dec 28, 2009 11:42 pm Post subject:

had this listed on another site too.

Tan Fbody carpet (lightweight)

I have a good full length tan, stock carpet from a LS1 firebird. Its the same as LT1 and v6 car. Maybe 3rd gens I'm not sure? I removed all the soft sound padding, and tar matting off the backside making it a lot lighter then stock. This will save you a lot of time and the PITA scrapping everything off ready to swap in. And if its too loud, you still have your stock carpet you could put back in to test it out.

the bad: I thought about doing a color change to dark gray, and with some of the duplicolor interior spray (paint) painted a little test square (4x4 IIRC) over the top of the gas tank area. to see how it matches. Was told that paint/dye sucks and rubbs/washes off easy and looks like crap in a short while. That looks to be true, if you rub over the spot some gray would come off on my hand. So with a little scudding with a brush, and some water/cleaner I htink it would wash out.

Looking to sell cheap, I saw some guys talk about removing the sound pading and remembered I had this.

But best thing is just use the front of them carpet, that molded all nice to fit the floor. And cut the rear off, and replace it with some really light ozite, or spectra carpet. In the rear parts thats flat over the hatch, the super light carpet fit that mint. And thats were the little test dye is anyway. Thats really the way to go, the super light ozite/specta is really cheap in shreds up.

Posted: Tue Dec 29, 2009 12:30 am Post subject: Re: 4th gen Fbody parts

	Upstate New York Club Grand Prix Forum Index -> Classifieds	All times are GMT - 5 Hours
Page 1 of 1