WTB stock parts. LOTS OF MODS FS!!!!

Posted: Wed Aug 22, 2007 9:26 pm Post subject:

updated sold parts
injectors
fuel pump
trailoing arms
_________________
New Era performance

01z28, M6 NA, mullet, T tops, siqqqq

Posted: Thu Aug 23, 2007 7:40 am Post subject:

Posted: Sun Aug 26, 2007 8:08 pm Post subject:

have 3 more sets on low milage GM yellow LS6 90# vavle springs

Posted: Mon Aug 27, 2007 9:05 am Post subject:

Hey,

I need a belt for my 3.3" pulley that's going on. Do you have a belt for that? What make and condition is it in?
_________________

Posted: Sat Sep 08, 2007 10:55 am Post subject:

pulley puller sold
Alt rewires sold
MSP upper mounts sold

Posted: Sat Sep 08, 2007 1:03 pm Post subject:

thanks for the help john, I'll definitely hit you up once I find out whats up with my job. nice meetin ya

Posted: Tue Sep 11, 2007 6:25 pm Post subject:

Any 60680 belts for the IC with 2.7-3.2 pullies?

Posted: Wed Sep 12, 2007 11:41 am Post subject:

probally not, I had 8ribs

Posted: Sat Sep 15, 2007 1:24 pm Post subject:

updated the list

sold ic,lim,fuel rails,

somone is gona have the fastest m90 car Cool

Posted: Sat Sep 15, 2007 1:44 pm Post subject:

you still have the s/c from your car i'm assuming since its not on that list? Wish i had the cash the day i was at your house i would have taken the ic lim and sc... Meeting a guy from Ohio and dropping my sled off to him in buffalo sept 29th. I may stop by and see what you have left on my way home.

Posted: Sat Sep 15, 2007 4:17 pm Post subject:

Posted: Sat Sep 15, 2007 7:13 pm Post subject:

I have the m90 that I was running last. The EGR is filled, you can drill out the filler, but I dont recomend it. It has new case bearings, also has a turned down snout to a 2.5. Snout in rebuilt to. I just realised I need a non turn down snout. I have 2, but with the stock pulley, your going to be able to tell somthing was done to the snout., so like to get a stock snout housing.

the list should be close to updated

Posted: Sun Sep 16, 2007 1:28 am Post subject:

ok, sounds good... I'll take it if you don't sell it by then, I can give you my whole stock s/c if you need it, just name a price and i'll take it. I can leave my stock pulley on there if you'd like, I haven't pulled it off to put the mps on yet. I've got an HPTuner so I can just delete the egr if its not on there Smile

no biggie. does it have a spot to bolt it up so it looks like its there? Wink

Posted: Sun Sep 16, 2007 9:42 am Post subject:

that might not read right.

I have 2 rebuilt snouts tunred down for a 2.5 pulley..FS $100

I have stock pulleys but if one comes on the snout, that works too. The ERG is filled in the blower, not the LIM. So you could hook up the EGR tubes. But Id just take it right out. No one is going to notice its gone.

Posted: Mon Sep 17, 2007 8:16 am Post subject:

ok, sounds good.

like i said, ill be out that way again on the 29th, so count on the s/c and snout as sold. does that s/c still have the hub attached to it? if so, i can just bring you that hub i showed you and save the trouble of pulling that off and exchanging them, as long as my pulleys will fit it Smile

	Upstate New York Club Grand Prix Forum Index -> Classifieds	All times are GMT - 5 Hours Goto page Previous 1, 2, 3, 4, 5, 6, 7, 8, 9 Next
Page 7 of 9